Cement Plant
Symptom Checker.

Above 50% life consumed from abrasive materials, contamination, or poor lubrication.

Baghouse issues, clinker contamination, or poor material flow cause repeated trips.

Above 1.5% from insufficient drying, high feed moisture, or hot gas problems.

Above 18% from separator inefficiency, worn classifier blades, or wrong air settings.

More than 20 mbar above normal from filter blinding, restriction, or overfeeding.

Above 18 kWh/t from inefficient grinding, harder material, or equipment wear.

More than 10% below design from worn elements, hard material, or classifier inefficiency.

Above 5 mm/s from uneven bed, roller skew, metal contamination, or bearing wear.

Above 120°C for VRM from moisture control failure or separator inefficiency.

Load swings above 15% from feed variability, moisture changes, or control issues.

Incomplete combustion, high CO, or insufficient secondary air temperature.

Rings restrict material flow, cause vibration, and reduce effective kiln length.

Critical safety symptom requiring immediate diagnosis to prevent kiln explosion risk.

Free lime above 2.5% indicates incomplete calcination or insufficient burning zone temperature.

Torque above 85% rated suggests heavy coating, overfeeding, or mechanical binding.

Below calciner exit -50°C suggests meal coating loss or cold air ingress.

Shell temperature above 380°C signals refractory failure, thinning lining, or coating loss.

Nodules under 5mm or over 50mm indicate combustion temperature or chemistry imbalance.

Unbalanced flame, poor fuel distribution, excess liquid phase, or raw mix issues.

Inefficient combustion, false air, AFR moisture, or high CO above benchmark.

Above 30% decomposition indicates calciner overflow or temperature imbalance.

Causes gas short-circuiting, efficiency loss, and dust carryover.

Sticky meal, high chlorides/alkalis, or temperature fluctuations cause cyclone strings.

Stage 1 above 400°C signals kiln backend instability or insufficient air balance.

Above 100 g/Nm³ indicates cyclone inefficiency or structural damage.

More than 20% above normal indicates buildup, blockage, or material accumulation.

More than 50°C above normal suggests cyclone efficiency loss or air leakage.

Restricts gas flow, causes shutdown, creates unstable operation.

Unbalanced flow, thermal cycling, or mechanical stress damage tower structure.

Below design -30°C reduces calciner temperature and secondary air quality.

Volatiles from AFR condense in cooler zones, creating sticky deposits.

Above 20% rise from fine AFR ash carryover or incomplete combustion.

Sticky AFR ash, low melting point compounds, or chloride/alkali cycling cause blockage.

±30°C swings from inconsistent AFR feed, variable calorific value, or dosing failure.

AFR ash interferes with clinker mineralogy via sulfates, phosphates, or heavy metals.

Above 2000 ppm indicates incomplete AFR combustion, reducing conditions, or poor distribution.

±15% swings indicate coating disturbance from AFR ash or thermal shock.

Above 300 mg/Nm³ rise from nitrogen-rich AFR or combustion staging failure.

Below target percentage from feed jamming, quality rejection, or stability limits.

Above 1.0% means unburnt AFR carbon, insufficient residence time, or low temperature.

Above benchmark reduces cooling efficiency, overloads grates, causes red carryover.

Above 95% indicates insufficient cooling capacity or system restriction.

Caused by clinker accretion, thermal stress, or mechanical overload.

Discharge above benchmark exceeds guarantee, reduces quality, stresses transport equipment.

Vent above 320°C indicates poor heat recovery or incomplete cooling.

Above benchmark signals clinker bridging, kiln rush, or excessive bed depth.

Improper distribution from static inlet, dust sliding, or air duct issues.

Below design -50°C reduces kiln thermal efficiency and increases fuel consumption.

Kiln discharge problems or inadequate crushing cause clinker accumulation.

Creates hot spots, dead zones, and variable cooling across the bed.

Less than 7 days between cleanings indicates excessive dust or poor combustion.

More than 300 Pa above design from tube blockage, dust buildup, or damage.

More than 30°C above design indicates poor heat recovery or tube fouling.

Steam below design -15% from fouled tubes, gas bypass, or low exhaust temperature.

Dust accumulation reduces heat transfer and increases pressure drop.

Chloride/sulfate attack, thermal stress, or material fatigue cause tube failure.

Above 20% open reduces steam output and wastes recoverable heat.

More than 15°C deterioration from fouling, scaling, or flow maldistribution.

Cavitation from water chemistry issues, insufficient NPSH, or control valve faults.

±2 bar swings from kiln instability, variable gas flow, or feedwater issues.